P0104 Engine Trouble Code

When you check engine light came on code P0104 the reason should be Engine Light ON (or Service Engine Soon Warning Light). However your vehicle's manufacturer may have a different definition for the P0104 OBD-II Diagnostic Powertrain (P) Trouble Code. So you should chech it on our car models.
When the DTC check engine light comes P0104 code on the first you can check is the gas related maybe gas cap. Pull over, retighten it, and take a look at the cap to see if it has any cracks inside. Go on driving and to see if the check engine light turns off automaticly. On the other hand, you can buy a gas cap for about $4.5 at an auto parts store. All you need to do is take the old one take off and take on the new one. If you've already bought it to the store, you might as well just replace the cap. While not car-threatening, it's good to take care of this right away to improve gas mileage/km.
P0104 Code Meaning :
OBD-II Diagnostic Powertrain (P) Trouble Code For Engine
Intake Valve Control Solenoid Circuit Low
Engine Oil Temperature Sensor Malfunction
Cylinder 10 Contribution/balance Fault
Clutch Position Sensor Circuit Malfunction
The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.
P0104 OBD-II Diagnostic Powertrain (P) Trouble Code Description
P0104 OBD-II Trouble Code The Mass Air Flow ( P0104 code. Engine Oil Temperature Sensor Malfunction and Cylinder 10 Contribution/balance Fault causes most of code P0104.
Reason For P0104 Code
The reason of P0104 OBD-II Engine Trouble Code is Engine Oil Temperature Sensor Malfunction.P0104 the main thing to check is to verify the operation of the VCT solenoid in the engine. You're looking for a sticking or stuck VCt solenoid valve caused by contamination. Refer to vehicle specific service repair manual to perform component tests for the VCT unit.
How To Repair P0104 Code
Before starting let's see P0104 repairing process steps:
- Qualified technicians will begin by using a scan tool to access P0104 code stored in the ECU.
- Technicians will note P0104 code present and any freeze frame data associated with them.
- After all, if you sure the engine trouble is finished, the code will be cleared.
As you idle at a light or before positioning your vehicle in gear and you see that your engine is starting to create strange sounds, switch your oil filter and also inspect the pressure regulator to attempt and adjust the error. If you struggle to start your vehicle and notice it fails to turn over right away, it can also indicate a defective fuel pressure regulator.
The computer installed in each fuel-injected vehicle has to be aware of two factors before it can solve the proper cold-start air/fuel compound: the engine coolant temperature and the exterior air temperature. Your symptoms are exactly the same to a faulty engine coolant temperature sensor (ECT). The computer is measuring an air/fuel compound that is excessively meager.
Sometimes P0104 code comes with P010400 code.Diagnosis Of Engine Error OBD Code P0104
It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a P0104 trouble code to be stored
The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the P0104 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.
The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.
Cars With Same Problems :
- Bsa Fwd P0104 Trouble Code
- Morris Oxford P0104 Trouble Code
- American Roadster P0104 Trouble Code
- Lloyd 650 P0104 Trouble Code
- Ssangyong Rodius P0104 Trouble Code
- Ford Fpv Gt-p P0104 Trouble Code
- Wartburg Estate P0104 Trouble Code
- Alpine A108-904 P0104 Trouble Code
- Ford 49 P0104 Trouble Code
- Lancia Ionos P0104 Trouble Code
- Toyota Fj Cruiser P0104 Trouble Code
- Daewoo Royale P0104 Trouble Code